Products
Yashanway Metal is the steel pipe producing and trading,Our factory making MS Pipe, Hollow Sections, Metal Plate/Coil, Pipe Fitting, Gypsum Board and Thermal Insulation Materials,all products with short delivery time, best quality and competitive price.
As a basic raw material, iron and steel products are widely used in various industries of the national economy, which is the "food" of industrial production - it can be used as a raw material to bury the whole sin in the production,manufacturing and consumption of other industrial products.
It is also a necessity in social life - can be directly used in construction, decoration and People's Daily life supplies.
Flanges are used to connect pipes, valves, fittings and special items such as filters and pressure vessels. The cover plate can be connected to form a "blind flange". The flanges are bolted, and the sealing is usually done using spacers or other methods.
The main use of flanges is to connect pumps, pipes, valves and other equipment to form the piping system. Usually, the flanges are threaded or welded and you can connect the two flanges with washer bolts and provide a seal to make the plumbing system easily accessible.
The main use of flanges is to connect pumps, pipes, valves and other equipment to form the piping system. Usually, the flanges are threaded or welded and you can connect the two flanges with washer bolts and provide a seal to make the plumbing system easily accessible.
The flange connection allows both materials to be connected through the inner and outer lips. Place decks between them to prevent any problems that may occur. Then, the installer uses the flange-fixing bolts. To ensure the tightness of the flange connection, the sealing element is used. To ensure a healthy seal, carefully align the flanges and tighten the bolts with the same torque.
Flanges are created in different sizes according on the intended application, and they are categorized based on different national rules and connection types. The highest heat and pressure values to be subjected to the system to be used, the potential rate of corrosion to be exposed to the line, and the location where the flange will be used are taken into consideration when choosing the type of material to be used in its production.
The pipe elbow is installed between two pipes so that the fluid direction can be changed to 45 degrees. The 45 degree bend produces less friction and lower pressure than the 90 degree bend.
The 90° elbow is used to connect two pipes at right angles to each other. In horizontal devices, they are used as corner ends or rail ends. In other words, a 90-degree bend is easily attached to pipes made of many different materials, including rubber, steel, cast iron, copper, and plastic.The 45° tube elbow is used to connect the pipe at a 45° tube angle. As the name suggests, this is a pipe fitting device that bends in such a way to change 45° of the fluid / gas flow in the pipe.
An elbow is the fittings used in a pipe system to connect two pipes of the same or different nominal diameter. It bends at a certain Angle, so that the straight pipe is connected at a certain Angle, so as to change the direction.
Since rectangular and square high speeds have about two-thirds of an open section of equal capacity, costs can be saved with fewer surfaces to be prepared, less paint material required, reduced cement fireproofing, and minimal labor.
A rectangular hollow section is a rectangular steel profile with a rectangular hollow section. These profiles have a wide range of sizes and can be manufactured with unique specifications.
The various types of cold rolled (dial) carbon steel pipes include general steel pipes, alloy steel pipes, high pressure boiler steel pipes, low and medium pressure boiler steel pipes, petroleum cracking pipes, and other steel pipes. Carbon thin wall steel pipes, alloy thin wall steel pipes, stainless steel pipes, and special-shaped steel pipes are also included in this category.
Carbon steel pipe has exceptional performance in terms of high yield strength, stress corrosion resistance, good weldability, and low sensitivity to welding hot and cold cracks.
There are two types of carbon steel tubes: hot rolled and cold rolled (drawn).
There are two types of carbon steel tubes: hot rolled and cold rolled (drawn).
The process of making LSAW pipes involves molding steel sheets around a cylinder and welding the ends together in a straight line. Typically, the diameter range of LSAW pipes is 16 inches to 60 inches (406 mm to 1500 mm). They perform well in terms of corrosion resistance at low temperatures and high pressure.
Depending on the various forming techniques used, longitudinally submerged arc welding pipe is separated into UOE, RBE, and JCOE steel pipes. With its quick continuous production and straightforward method, longitudinal high-frequency welded steel pipe finds extensive application in the light industrial, petrochemical, and civil construction industries, among other areas. mostly utilized in the transportation of low pressure fluids or manufactured into different engineering parts and light industrial goods.
no data
Contact Us
Adds:
B-508 Xiangnian Plaza, Dongjiang Road, Hexi District, Tianjin China
Contact person: Crystal
Tel: +86 18602606269
WhatsApp：+86-18602606269